Gadget part list
----------------
This is fairly accurate, although there are still some unknowns as described in the notes.
Unit x30
ID ITEM Price Bought Quant Cost Source Notes
-- ---------------- ----- ------ ----- ---- ------ ------------
E1 LK202 LCD display 0.00 Y 1 0.00 Cary
E2 speaker 0.50 1 15.00 Halted May use piezo instead
E3 knob 0.95 Y 1 28.50 Halted the silver one
E4 AAA battery 0.33+ 4 39.60+ Digikey May need more expensive ones
U1 PIC 18F252 MCU 0.00 Y 1 0.00 Microchip
U2 voltage regulator 1.886 1 56.58 Digikey LM2936
U3 IR Receiver module 0.90 1 27.00 Digikey GP1UM26XK
X1 32768Hz crystal 0.89 Y 1 26.70 Halted
S1 encoder 5.06 Y 1 151.80 Cary
10uf Cap 0.064 Y 2 3.84 Halted decouple & audio
C1
C4
22pf cap 0.05 ? 2 Halted for crystal
0.04 2 2.40 Halted (33pF bought for 0.04 ea)
C2
C3
47uF Cap 0.064 Y 1 1.92 Halted for IR Receiver
resistors 0.02 12 7.20 Halted
R1 470K
R2 3K
R3 50K
R4 600 ohm
R5 1K
R6 8.2K
R7 8.2K
R8 1K
R9 10K
R10 47 ohm
R11 1K
R12 100 ohm
3906 PNP Transistor 0.10 5 0.50 Halted
Q1
Q2
Q3
Q4
Q5
1N4002 diode 0.04 2 2.40 Halted
D1
D2
wire .02/ft 3ft 1.80 Halted rough guess
PCB ? 1 112.60 APCircuits 2" x 1.5" w/ 100 holes
case ? 1 ? ?
----
477.84
477.84/30 = 15.93 ea
===============================================================================
Clue site IR transmitter
------------------------
This is a very rough estimate
Unit x30
ITEM Price Quant Cost Source Notes
---------------- ----- ----- ----- ------ ------------
PIC 16F628 1.50 1 45.00 Digikey rough guess on price
crystal 20MHz 0.00 1 0.00 Display Use one from display board
crystal caps 0.00 2 0.00 Display Use one from display board
battery 0.00 1 0.00 Karl Free NiCad's from Karl?
TX LED 1.77 4 212.08
3904 NPN transistor 0.10 4 12.00 Halted maybe only need 1?
vreg 1.06 1 31.80 ?
PCB 1 70.00 ?
case ? 1 ? ?
----
370.88
Quant cost +477.84
----- ------ -------
30 370.88 848.72
20 317.26 795.10
15 255.44 733.28
10 293.63 771.47
5 131.82 609.66
================================================================================
NOTES:
- Assumes transmitter PCB and main PCB on same board
- We can probably use some flash PICS that I already own for the transmitters so the cost could be 0
(since I can have them back afterwards)
- The price for the gadget is likely to go up as we add stuff and if we add an expensive case and PCB
|
This file Copyright (C) 2004 by Nathan (Acorn) Pooley
Go to DRUID Development page
Go to DRUID page
Go to JU Gadgets page
Go to Justice Unlimited homepage
Go to Acorn's personal webpage
Contact Acorn
See comments from others
Post your own comments
File created by do_doc at Wed Aug 4 18:08:36 2004